How to send a file to a die-cutter or plotter
User guide contents ↓The cut file comes from die-cut sticker nesting with automatic cut contours. Before exporting, pick where the cut line goes under Die-cut settings → Cut line in the PDF. The two options suit different machines:
| Option | What the PDF contains | Suits |
|---|---|---|
| Separate page (default) | Print sheets first, then one last page with only the cut line: a solid K100 black stroke, 0.2 mm, no artwork | Die-cutters and plotters whose software imports the cut path as its own file or layer (for example an Illustrator or CorelDRAW workflow) |
| Same page | Each print sheet carries its cut line on top: a 0.2 mm stroke in a spot color named CutContour, overprinted, on its own layer |
Print-and-cut machines whose RIP reads a named spot color as the cut path (for example Roland VersaWorks) |
Either way the cut line uses the exact same sheet size and position as the artwork, so it lines up with every label. The PDF's document properties also note which page is which.

Steps with a separate cut-line page
- Click Export print PDF + cut line.
- Print the print pages as usual at 100% / Actual size.
- Open only the last page (the cut line) in your cutter software (Illustrator, CorelDRAW or the software bundled with the machine).
- Place it at the sheet's origin, then mark the stroke as the cut path the way your software requires.
- Cut one test sheet and check alignment before running the whole batch.
Steps with the cut line on the same page
- If your RIP expects a name other than
CutContour(for exampleThru-cutorCutContour2), type it in Spot color name before exporting. Names are case-sensitive. - Click Export print PDF + cut line and send the PDF straight to the RIP.
- The RIP prints the artwork and keeps the spot-color stroke as the cut path, so it is not printed.
- Run one test sheet.
Tip: If the cut is shifted evenly in one direction, the cause is usually paper feeding or loading, not the file. If you only need the cut a little further out or in, change Cut line offset +- during imposition; see Die-cut nesting.
Why a separate page exists
Many cutter programs only need the cut path, not the artwork. If the cut line were mixed into the print page, you would have to delete the artwork or hide layers by hand, and it is easy to cut the wrong thing. The separate page contains nothing but the 0.2 mm K100 stroke, so it drops straight into the machine software while the print pages go to the printer.
Because both pages share the same sheet size and origin, never change the paper size or scale when printing: at the wrong scale the print and the cut line drift apart.
Checklist before a production cut
- The print pages were printed at 100%, not "Fit to page".
- The real paper size matches the sheet size in Trimto, and the paper is loaded straight.
- The cut line sits at the correct origin and is set as the cut path in the machine software.
- You cut one test sheet and measured any offset with a ruler.
- Blade depth, force and speed suit the material (vinyl, sticker paper, card).
When the cut is off
| Symptom | Likely cause | Fix |
|---|---|---|
| Shifted evenly to one side | Paper loaded off-center, or the printer stretches the paper | Re-align the origin; use your cutter's registration system (see below) |
| Drift grows toward the far edge | Printed at a scale other than 100% | Reprint at 100% / Actual size |
| Blade cuts into the artwork | Cut line too close to the label edge for the machine's accuracy | Increase Cut line offset +- |
| A thin white edge remains | The cut lands outside the artwork, or the design has no bleed | Lower Cut line offset +- to 0 or slightly negative, or add bleed to the design |
Registration marks for camera or sensor cutters
Trimto's optional Registration marks are crosshairs for checking print registration by eye. They are not the optical marks that contour cutters scan to find the sheet (Summa OPOS, Graphtec ARMS, Silhouette registration marks). Add those in your cutter's own software or RIP, and keep a white margin of about 10 mm around the label block (raise the Safe margin) so there is room for them.
Further reading
- Roland DGA, File preparation for print/cut production: how a CutContour spot color becomes the cut path.
- Summa, Benefits of OPOS camera cutters: how contour cutters read registration marks.
- Adobe Acrobat Help, Adjust page size for printing: printing a PDF at actual size.
- Wikipedia, Vinyl cutter and Spot color.