EN
Open the tool

How to fix a PDF that prints at the wrong size

User guide contents ↓

Updated Nov 12, 2026 · Open the tool in a new tab ↗

Trimto always exports PDFs at the exact real size of your sheet and labels. When a print comes out the wrong size, the cause is almost always a setting in the PDF viewer or printer driver, not the file.

Print now and Export print PDF buttons: the file always keeps the exact mm size
Print now and Export print PDF buttons: the file always keeps the exact mm size

Labels printing smaller than designed

Cause: The print dialog has Fit to page or Shrink to fit selected, causing the printer to scale down the design to fit within the sheet margins.

How to fix: Set the scale to Actual size, 100%, or Original size. This applies when printing from Adobe Reader, a browser PDF viewer, or the Print now button in Trimto.

Edges cut off or shifted to one side

  • Sheet size in printer settings does not match the file size (e.g., file is A3, but printer is set to A4). Select the exact sheet size loaded in the tray.
  • Safe margin is too small for your printer's non-printable margins (typically 3–5 mm). Increase the Safe margin during the imposition step.
  • Crop marks fall outside the sheet edges: with step & repeat, Trimto keeps 5 mm free around the label block for crop marks; if that still does not fit, it shows a warning. Increase the safe margin or reduce the label count.

Double-sided prints do not align

  • In the printer dialog, pick the duplex edge that matches the Flip type you chose in Trimto (the table in Print double-sided step and repeat maps them to long edge and short edge).
  • A small, constant shift between front and back is the printer's mechanical tolerance: measure it on a test sheet and enter it in Back offset X, Y.
  • For manual double-sided printing: reload the stack turned over the same way as the flip type, and run a single test sheet first.

Quick check

Print one sheet, measure one label with a ruler, and compare it with the size Trimto shows on each design in the left column. A uniform shrink (e.g., down to 97%) indicates a Fit to page issue; a positional shift indicates a sheet size or paper-feed orientation error.

Why Trimto always exports exact mm

A PDF describes the page in absolute units. Trimto places each label at its real size (mm) on a page with a defined sheet size, so the file never scales itself. Any difference comes later, in the viewer or the printer driver, when they "fix" the file to fit the paper.

Checking order when a print is wrong

  1. Print scale: is it on Fit to page? Switch to Actual size / 100%.
  2. Paper size: does the size in the print dialog match the file and the paper in the tray?
  3. Non-printable margin: many printers skip 3–5 mm at the edge, so labels near the edge get clipped.
  4. Orientation: does portrait / landscape match the file? A printer that auto-rotates shifts the labels.
  5. Viewer test: open the exported PDF in a different viewer (browser, Adobe Reader) to tell whether the fault is in the file or in the printer.

Quick table: symptom and cause

Symptom Common cause
Every label evenly small (e.g. 97%) Fit to page
Whole sheet pushed to one side Paper size or printer margin
Labels near the edge clipped Printer's non-printable area
Back side upside down Wrong flip edge in duplex printing
Shift grows toward the end of the sheet Paper fed in skewed

When you need exact output

For jobs that demand precision (die-cut labels, small stickers), print one test sheet, measure with a ruler and note the error. Never correct it by changing the print scale. A constant shift of the whole print comes from paper feeding: re-align the origin in the cutter software, or use Back offset for the back side of a double-sided job. If the cutter cuts slightly into the artwork, increase Cut line offset +-. See also How to preview and export a print-ready PDF.

Further reading

  • Adobe Acrobat Help, Adjust page size for printing: where the scaling options are in Acrobat and Reader.
  • Wikipedia, Paper size: why an A4 file on Letter paper (or the reverse) gets clipped or shifted.